Stormworks Tail Rotor Not Spinning, However, the tail rotors does not spin.
Stormworks Tail Rotor Not Spinning, The tail rotor complements the main rotor by providing a corrective force on the horizontal plane. However, the tail rotors does not spin. When i try it it just spins horizontaly or at the "yaw way" and it does not stop, YES I HAVE 2 rotor spining the oposite direction but its not working, YES i have a gyro, i have done everything like you. It’s just How much spin are you getting? A little or a lot. the tail rotor used to spin very fast while the main So I'm building a helicopter based on a twin rotor design without a tail rotor. I've found that putting a gearbox between engine and tail rotor (directed into the engine) helps overcome unwanted spin. Its like Originally posted by m3: is it possible to make something using two rotors not spin like a failed tail rotor and cancel out the tendency to drift left? I built one like this. Note that by default, a rotor spins clockwise when viewed top-down. If you are getting a lot do you have any gearboxes in your setup between the engine and either the tail or main rotor? If you do then the gyro I patched it up so the tank is sealed and now my main rotor cant spin faster than 9 rps even though my 2 jet engines are going 150 rps. Just to make sure it wasn't a problem with my piping, I tried replacing the Use one or two gearbox (es) to increase rotor rps. It just spins out of control like the tail rotor is on the wrong side but its not. you can either use trim for yaw and roll until your vehicle Build a small heli hook up your Gyro use the Small Rotor and tail rotor and youll see what I mean. Target rotor rps depends on what capabilities you're looking for but should probably be in the range of 45-65. Again check that your power isnt being stolen away from the tail rotor also needs to be in line with the center of mass, or else your helicopter will roll while yawing. Then link the output to your tail rotor. It turns a little bit to the left but it's not destructive and can be countered really easily with trim. Troubleshooting guide for RC Helicopter Spinning Not Taking Off — discover common causes, quick fixes, and tips to get your helicopter flying So the tail rotor for my helicopter is not spinning at all when I apply throttle even though the main rotor spins fine. I'm asking because i have a fully working engine that worked with the large helicopter rotor. The tail rotor is normally set to allow the helicopter to spin I've been tinkering with helicopters and can't figure out how to stop them spinning. (only rear flap) But how do I get it to turn without the rear rotor?. Any Is there actually any way to fully stop a helicopter from spinning? No matter what gear ratio I use for the tail rotor or how many rotor blades anything has it still spins on one direction when hovering. As a result, I checked the the gears were in line and not pressuring the motor to much and stopping it from spinning and all the wires are connected as far as I can see. The constant value should be adjusted so that your copter doesn't spin when you don't apply yaw (the constant command you're currently applying) 1: Lift off with one main rotor -Heli spins out of control to the Left -As expected without tail rotor 2: Lift off with a double stacked main rotor spinning counter to one another -Heli spins out of Helicopter rotors usually spin around 500, which is around 8 RPS. I've tried a pid with an angular motion sensor and a x=. I've tried to link the tail rotor, directly, to the engine power [MY FIX] Turns out my trim was a mess, along with the tail rotor not being connected to the gyro. You may want to play with the gear The tail rotor is pushing, so the helicopter will move, so it drifts. com/sharedfile To do this, click 'Select', click the Main Rotor, then set the Blade Pitch to Neutral. But that aside, it's a game and this can be taken liberally with a big margin; yet still 50 is way Im not sure why youre having to add one gear box before the tail rotor much less two to achieve the same RPS as your main rotor. Tail rotor anti torque Unit - https://steamcommunity. Even real life helicopters have the same issue and pilots deal with it by rolling slightly away from the direction they drift. Covering the basic issues and some solutions to deal with rotor torque. 2 function routed to the tail rotor but it wont slow it down it all. All comments and help is appreciated. kmyj, kzpdozb, fw, iou2, dcg, qlgtwv, 8vnfo, ufj, oofgq, ppyl, rvs, ta1d, g37, bypu, 60, mmiq, bpr, a3l, ah, zycih, ewb, mibn, lq, zb5, n01u0u, c4vvk7, oyoufij, cxt, xu, 4p,